NDT TRAINING IN CHENNAI | NDT COURSE IN CHENNAI | COURSE NDT IN CHENNAI | TRAINING NDT IN CHENNAI | COURSE INSTITUTE OF NDT TRAINING IN CHENNAI | COURSES NDT IN CHENNAI | TRAINING FOR NDT IN CHENNAI | NDT TRAINING CENTER IN CHENNAI | NDT TRAINING CENTER IN CHENNAI CENTER IN CHENNAI | NDT TRAINING CENTER IN CHENNAI | NDT TRAINING IN CHENNAI | NDT IN CHENNAI | NDT COURSE CHENNAI NDT TRAINING IN INDIA, NDT COURSE IN CHENNAI NDT TRAINING CENTER IN CHENNAI COURSE IN INDIA, NDT IN CHENNAI, NDT IN CHENNAI, NDT COURSE IN CHENNAI , NDT IN TAMIL NADU, NDT NDT COURSE , NDT TRAINING CENTER IN CHENNAI, NDT TRAINING & CERTIFICATION IN INDIA, NDT INSTITUTE IN CHENNAI | NDT IN DELHI | NDT IN CHENNAI.

    TIME-OF-FLIGHT DIFFRACTION (TOFD)

    Time-of-flight diffraction (TOFD) method of ultrasonic testing is a sensitive and accurate method for the nondestructive testing of welds for defects. TOFD originated from tip diffraction techniques which were first published by Silk and Ludington in 1975 which paved the way for TOFD. Later works on this technique are given in a number of sources which include Harumi et al. (1989), Avioli et al. (1991), and Bray and Stanley (1997).


    Bray and Stanley (1997) summarized TOFD as tip-diffraction techniques which utilized the principle that the tips of a crack when struck by a wave will diffract the signals back to the other location on the surface. The depth of these tips can be determined from the diffracted energy.


    TOFD was invented in the UK in the 1970s initially as a research tool. The use of TOFD enabled crack sizes to be measured more accurately, so that expensive components could be kept in operation as long as possible with minimal risk of failure.


    Measuring the amplitude of reflected signal is a relatively unreliable method of sizing defects because the amplitude strongly depends on the orientation of the crack. Instead of amplitude, TOFD uses the time of flight of an ultrasonic pulse to determine the position of a reflector.


    In a TOFD system, a pair of ultrasonic probes sits on opposite sides of a weld. One of the probes, the transmitter, emits an ultrasonic pulse that is picked up by the probe on the other side, the receiver. In undamaged pipes, the signals picked up by the receiver probe are from two waves: one that travels along the surface and one that reflects off the far wall. When a crack is present, there is a diffraction of the ultrasonic wave from the tip(s) of the crack. Using the measured time of flight of the pulse, the depth of a crack tip can be calculated automatically by simple trigonometry. This method is even more reliable than traditional radiographic, pulse echo manual and automated weld testing methods.



    1. Features :

    • A computerised and automated system for weld inspection.

    • Probes are mounted on a buggy that travels along a weld, recording data as it moves.

    • Compared to conventional methods of ultrasonic testing, TOFD is sensitive to cracks and measures their dimensions accurately.

    • TOFD has two blind zones where it is not sensitive to defects, hence TOFD ought always to be supplemented by a conventional pulse-echo examination of the near and far walls. The pulse echo probes are commonly mounted on the same buggy as the TOFD probes.

    • Requires ultrasound technicians with advanced training.

    2. Standards :

    • International Organization for Standardization (ISO)

    • ISO/DIS 10863, Welding – Use of time-of-flight diffraction technique (TOFD) for examination of welds European Committee for Standardization (CEN)

    • EN 583-6, Non-destructive testing – Ultrasonic examination – Part 6: Time-of-flight diffraction technique as a method for detection and sizing of discontinuities

    • EN 15617, Non-destructive testing of welds – Time-of-flight diffraction technique (TOFD) – Acceptance levels

    • Inspection of Welds

    • Thickness measurements

    • Corrosion inspection

    • Flaw detection



Copyright © 2015

TWG GROUP

Designed by   TWG GROUP